DIY dog booth: stages of work.
The first thing to do is cut all the necessary parts according to the plan. Do not forget that in addition to plywood, you will also need 80×40 timber. In addition, if you will be using a circular saw, remember that when marking out, take into account the thickness of the blade with which you will cut.
Then assemble the structure by attaching the plywood to the beams with self-tapping screws.
Assembling the booth from finished parts does not take much time. It remains for us to install an internal partition and a roof.
We also doubled the floor in the main room to minimize heat loss.
And our booth is actually ready.
If the dog has to spend the winter in this booth, then it makes sense to fill the space between the plywood sheets with insulation. Insulation can also help keep the booth cooler during the summer months. However, you should not use vapor-permeable insulation such as mineral wool, as they can pick up moisture in the off-season, which can reduce their effectiveness to zero.
Use solid, vapor-proof insulation such as extruded polystyrene foam. It is sold in sheets of various thicknesses, and is absolutely not afraid of moisture, so it does not lose its properties in wet weather. It can be used to insulate not only the walls, but also the floor and roof of the booth.
When installing, it is advisable to tilt the roof slightly towards the rear wall so that water can drain from it.
Obviously, the plywood on the roof will quickly get wet and become unusable, so you need to cover it with any roofing material that you have at hand: everything from roofing material to metal tiles will do. It’s time to use the leftovers from the roof of a house or garage.
That’s all! The booth is ready to move in. For beauty, you can sheathe it outside with clapboard.
Important! And the last small, but very important detail: try to raise the booth above the ground. You can attach legs to it from below, or just put it on bricks, but in any case, provide some clearance between the floor and the ground. This will not only help the dog dry out and warm up in cold weather, but will also extend the life of the booth, because its bottom will not be exposed to excessive moisture.
DIY dog booth: 60 photos, drawing and instructions
Every dog living in the yard of a private house needs a reliable shelter that will protect from bad weather and help keep warm on a cold winter night. A do-it-yourself dog booth does not require much time from you, nor a large amount of materials, nor outstanding builder skills.
Insulated booth for a dog: drawings.
There are many ways to build an insulated doghouse, but we will focus on just one of them. This method combines two techniques at once that make the booth warm.
2. And secondly, the walls of the main compartment are made double. The air gap between them will significantly reduce heat loss, and the animal will be able to quickly heat a small space inside the booth with the heat of its body.
Our kennel is designed for medium-sized dogs (up to 50cm at the withers). If your pet is much larger or, on the contrary, smaller, then it may be necessary to proportionally increase or decrease the size of the booth so that the dog is comfortable.
Another design trick worth taking in is the removable roof.
You can make it open like a chest lid. all you need is a couple of hinges. But a booth with such a roof can be easily cleaned if necessary.
DIY dog booth: design options
It’s good when the dog house fits harmoniously into the overall design of the site, so we offer you several interesting design options.
Dogs often like to sit on an elevated position off the ground, especially during wet seasons. You can supplement the basic structure of the booth with additional extensions.
Your dog will appreciate it, of course, why not please him?
As you can see, there is nothing complicated in the basic design of an insulated doghouse. And small, simple additional details will give it great practicality and convenience for your four-legged friend. A do-it-yourself dog box will become a home for your pet, in which he will feel like a full-fledged owner. Treat your dog to a great home and you can be sure it will repay you with loyalty and love.
Do-it-yourself dog booth: step-by-step instructions for creating housing for a dog
DIY dog booth
Materials and tools needed to make a do-it-yourself dog kennel
In order to make a booth with your own hands, you must use environmentally friendly materials, it is best to use a tree (conifers). For construction, lining is used, 12.5 mm thick (outer cladding), as well as fiberboard, chipboard, plywood and floorboard. You will also need bars in sizes 100100, 4040 and 10050. To create external corners and decor of the booth, use a wooden corner, as well as a symmetrical baseboard and decorative slats.
To insulate the booth (and this must be done), they use glassine, foam and mineral wool. The roofing material of the booth will be a galvanized profiled sheet or slate. It is not recommended to use bituminous tiles and roofing felt for these purposes, because. Out of habit, the dog will gnaw them and thereby harm its health.
The tools that we need to make a booth with our own hands are as follows:
- Building level
- Hacksaw or circular
- Galvanized nails
- Paint (pinotex)
- Drying oil
- Antiseptic impregnation for wood
Choosing the size of the dog booth
Dimensions of the dog house
The first step is to determine the size of the dog booth. To do this, we determine what kind of dog you have in size. There are 3 types of dogs: small, medium and large. Accordingly, dachshunds and similar dogs are referred to representatives of small ones, German shepherds are medium-sized, and Caucasian shepherd dogs are large. Based on this classification, it is customary to make booths of the following sizes:
- For small dogs: 700 550 600 mm (where the length is the first and the height is the last)
- For medium dogs: 1200 750 800 mm
- For large dogs: 1400-1000950 mm
The size of the doghouse is allowed to be adjusted based on the dimensions of your own dog.
In order to correctly determine the size of the booth, you must adhere to this technique:
- In order to correctly choose the width of the hole, measure the width of the dog’s chest and add 5-8 cm to this value.
- The ideal height of the manhole is 5 cm below the height of the dog’s withers.
- The height of the booth should be 5-8 cm at the withers.
- The depth of the booth equals its height (except for some dog breeds, which dictate their own booth dimensions)
Calculating the size of the booth
As mentioned earlier, the size of the booth can be slightly “moved”, but only to a larger value, especially if the booth is being built for a puppy.
During the construction of the booth, it is necessary to be aware of the following points:
- Housing for the dog should be comfortable so that it can lie down, turn around or stand up.
- The inlet should not be narrow, it is better, on the contrary, slightly widen it for convenience
- The booth must be covered with insulation so that the dog does not freeze in the winter
- The walls and roof must provide reliable protection from wind and precipitation
- The material for making the booth must be environmentally friendly so that the dog does not spoil its health while living in the booth (it is best to use wood)
- The booth must be correctly located in the backyard (the side must not be windy, and the dog must see everything that happens on the territory)
- The roof can be either single-pitched or double-pitched, there is no big difference
- For convenience, make a small attic under the roof of the booth, in which you can put dog toys, dishes and other accessories
- The manhole must be built in the direction of the long wall, so that the dog can more conveniently climb into the booth
If you are the owner of a large dog, it is recommended to build a booth in a dog enclosure, which is also not difficult to build with your own hands.
After we have decided on the size of the booth, we proceed to sketching a drawing, with which it is easier to build a booth with our own hands.
How to make a dog kennel: step by step instructions
First of all, we cut the boards. In the event that the roof is single-pitched, the rear wall of the booth should be shorter than the front one so that the rainwater slope behind the booth.
We prepare wooden blocks for the booth frame. Better to make the length of the bars with a small margin.
We knock off the frame of the booth in accordance with the previously prepared drawing
We sheathe the frame of the booth from the inside with boards, it is immediately recommended to build a roof. So that the dog does not get hurt, the boards must be sanded.
We construct a manhole in the front wall of the booth, the ends of which also need to be processed
Now we turn to insulation: we must insulate the floors, walls and roof with foam, on top of which the outer wall of boards will be fixed.
We insulate the floor of the booth
After that, we sheathe the outer part of the booth using the material of your choice (fiberboard, chipboard, lining, etc.). Wood siding is recommended if material permits.
We sew and insulate the frame of the dog booth
Next, we proceed to sealing cracks and seams so that wind and precipitation do not worsen the dog’s cozy location. As a sealant, you can use slats, plinths, glazing beads, etc., the main thing is that they are wooden.
After sealing, we move on to the roof of the roof. For this, it is best to use slate sheets.
Well, in the end, it remains to treat the finished dog booth with an antiseptic and install the building on bricks or a pallet so that the floor does not rot on damp earth
That’s all, the do-it-yourself doghouse is ready! It remains only to paint it and install it in a suitable place.!
Ready kennel for a dog
Drawings of a dog house
As soon as the drawing, and therefore the type of housing for the dog, is chosen, we proceed to creating a booth with our own hands.
Photo of dog booths
Another similar article: do-it-yourself birdhouse for the garden, go in and read!
First, the frame of the doghouse is lined with glassine from the inside. It is fixed in the corners with a stapler. Then foam or mineral wool is fixed. Then the insulation is covered with glassine, on top of which plywood is fixed. She is also laid on the floor.
Installation of cladding on walls
For the external cladding of the structure, lining is used. Then they insulate the frame of the dog booth from the inside. First, glassine is fixed with staples. Then styrofoam or mineral wool is laid between the bars. Further, the insulating material is covered with glassine, which is covered with plywood. You can also use chipboard or any other similar material for this. Small zinc-coated nails must be used to fix the sheathing. At the same time, their hats should always be sunk into the tree so that the dog cannot get hurt.
Sheepdog booth. Photo master class
Do-it-yourself booth with a vestibule
To make the dog booth more comfortable, you can build it with a vestibule. Such a dwelling for a dog will consist of two sections:
- The far part, which is a sleeping place;
- Lower part for increased protection against cold and draft.
The compartments are separated from each other by means of an insulated partition, in which the access hole is located.
It is not so difficult to make a kennel for a dog, but during its construction it is not recommended to make a large sleeping place, since almost all dogs curl up while sleeping. At the same time, it is necessary to provide for the opportunity for the animal to stretch freely in the vestibule when it rests in this place. Therefore, the size of such a part of the house should correspond to the height of the dog.
Booth for a dog with a vestibule. Dimensions and drawing
The assembly of the structure with a vestibule takes place in the same way as other booths. A distinctive feature of such a house is the partition between the two sections of the dog’s dwelling. It is created from bars with a section of 40×40 mm, plywood, insulation material and self-tapping screws. First, a frame is made, the dimensions of which correspond to the width and height of the booth room. Then plywood is nailed to it, on the one hand. Then insulation is laid in it, on top of which another sheet of plywood is fixed.
In order for the partition to be easily removed, the need to take two slats from wood and select longitudinal grooves in them using a cutter. Their width should be equal to the thickness of the partition. After that, the slats are fixed on the walls of the booth. After that, it remains to insert the partition into the created grooves.
A booth with a gable roof. Master Class
It is recommended to create roofs with two slopes on small booths, because such structures increase the weight of structures that are inconvenient to lift during cleaning.
Drawing of a dog house
Two structures are made, for each of which two bars of 50×50 mm are used. They are connected to each other so that an angle of 40 degrees is obtained between them. The workpieces are installed vertically on the frame flush with the smaller walls and fixed temporarily with nails. Two installed blanks at the top points are connected horizontally with a bar with the same section. In this case, it must be provided that it protrudes 200 mm in front of the kennel. Further, two bars of the same length are fixed at the lower points of the rafters.
The bottom frame is made of four bars, each side of which is 50 mm. In its corners, racks are fixed in a vertical position. Their size should correspond to the height of the booth. In the upper part, they are tied with the same bars. The strength of the doghouse frame is increased by attaching additional jumpers to the bottom and on both sides of the manhole.
How to make a kennel for a dog. Step by step photos
The frame, sheathed, on one side, with boards, is turned upside down. Its inner part is covered with glassine, which is fixed with staples from a stapler. Then the foam is laid between the beams. This material is cut according to the dimensions of the frame, and its thickness should be equal to the height of the beams. Then the insulation is covered with a layer of glassine and a finished floor is created.
Creating a frame for the bottom
In accordance with the drawing of the doghouse, bars are taken, each side of which is 40 mm. They are cut to fit the bottom. Then a rectangle is formed from them on a flat surface. Its corners are fixed with self-tapping screws. If the dog is large, then the frame must be reinforced. For this, additional jumpers are fixed in it. Then she, on the one hand, is sheathed with boards.
Do-it-yourself shepherd booth. Photo step by step
Dimensions of the dog house
- For small breeds such as dachshund, 700 mm long, 550 mm wide and 600 mm high;
- For medium sized dogs similar to a German shepherd, 1200 mm long, 750 mm wide and 800 mm high;
- For large animals in which the height at the withers is approximately the same as that of Caucasians, 1400 mm long, 1000 mm wide and 950 mm high.
The size of the dog house can be adjusted depending on the actual dimensions of the dog. So, his chest should pass freely into the opening of the structure. Therefore, it is necessary to add from 5 to 8 cm to its width. In this case, the best manhole height is equal to a value that is 5 cm less than the height of the dog at the withers. At the same time, the maximum vertical size of the booth and its depth should be 5-8 cm more than the height of the animal at the withers.
Dimensions of the dog house. A photo
The size of the booth can be changed, but only upwards. It is especially important to follow this rule when the design is created for a puppy. When building a dog booth with your own hands, you should always remember the following points:
- Nothing should interfere with the dog in his home so that he can freely lie down or become.
- The inlet must be comfortable. To do this, it can even be slightly increased in size.
- The structure for the dog must be insulated so that the dog is warm in winter.
- The roof and walls of the structure must reliably protect the animal from different precipitation and wind.
- The booth must be built from environmentally friendly materials. It is best if it is made of wood, since wood is harmless to the health of the dog.
- The structure must be placed on the territory of the personal plot from the windless side. In this case, the dog must have maximum visibility.
- A good version of the booth is a structure in the roof of which there is a small attic where you can store various things, including toys and dishes for the dog.
- Laz is recommended to be performed on a short wall. Thanks to this arrangement, it will be more convenient for the dog to climb into his home.
- Before creating a structure for a dog, you must carefully calculate the size of the booth. It is best to double-check the dimensions several times. This will build the perfect structure for the animal.
Dog house care
After the kennel is made, installed and a permanent tenant settled in it, you need to know how to care for it. You need to regularly clean your pet’s house. It is advisable to do the cleaning monthly. In the summer, disinfect once a month, and in the rest of the year. once a season.
In the process of cleaning, remove scraps, gnawed toys, treat walls and floors with a parasite repellent. Let the dog into the booth only after the solution has dried.
What material is better to make a booth
The owner of the animal himself determines the size of the structure and its location. First, the material for construction is selected. Next, calculate the need for building material.
You need to decide which materials are suitable for creating a pet’s housing, and which are not:
- Varnished or painted materials heat up in the sun and give off an unpleasant odor. Can cause animal allergies.
- Metal structures bring discomfort to the animal during hot and cold seasons. The metal heats up in the sun and it gets too hot in the kennel. In winter, in such a house, the pet will be very cold.
- Do not make a slate roof. This material is harmful to both human and animal health.
- It is better to refuse insulation with expanded polystyrene, polyurethane or various types of pressed wool. These materials give off odors, which can reduce pet’s sense of smell and allergies.
- A box made of pressed wooden panels quickly loses its strength, and in winter it can completely collapse.
For the manufacture of shelter for dogs, planks made of conifers are best suited: pine, spruce, cedar. To insulate the kennel, natural materials are used that will not cause allergies in the animal. The roof is made of metal or from ondulin. A mattress filled with sawdust or straw is laid on the floor, on such a bed the animal will sleep comfortably and warmly.
How to build a dog house for the winter
There are different opinions about warming a dog kennel for the winter. Some pet owners believe that a warm booth is needed only for smooth-haired dogs. It is worth remembering that a harsh winter presupposes severe frosts and an animal, even with long hair, will be cold. Therefore, for the comfort of the pet, the booth is insulated.
The winter dog house is insulated inside and out. They insulate the floor, and use curtains for the manhole. To make the pet’s housing warmer, it is installed on logs. For internal insulation of walls and floors, felt or batting is used. For external insulation, foam is taken. The blind on the manhole is made of dense and durable fabric or silicone.
If you decide to make a booth for a husky with your own hands, it is better to make it larger. The animal loves space and in winter it enjoys spending time in the snow, it will be too hot in a cramped kennel. The mat is not used on the floor or it is laid very thin. A not very dense fabric is hung on the manhole, which allows air to pass through well.
Also, like huskies, husky dogs prefer coolness. To make a do-it-yourself husky booth, drawings and dimensions can be used the same as for a husky. Straw bedding in the kennel is fine for this breed. Insulation for the booth is better to choose breathable air, pets of this breed do not tolerate stuffiness.
Malamutes also love fresh, cool air during the winter. The dimensions of the Malamute booth are the same as for the husky booths, and huskies, all three breeds belong to the middle group.
A booth for a thermophilic Labrador should be well insulated. The animal will also not refuse a warm litter. The size of the Labrador booth should be optimally selected. In a too large kennel, the dog will freeze, in a small one it will be cramped and uncomfortable. For thermophilic breeds such as Golden Retrievers, Dalmatians, Beagle and Drathhaar, the size of the booth is also very important.
Location of the booth on the site: basic rules
The place for the doghouse is chosen thoroughly, because the animal will spend more than one year of its life here. The location should be convenient for both the owner and the animal, and must comply with certain rules:
- The booth is located next to the front door of the house;
- From the side of the kennel, the entrance to the site and most of the yard should be clearly visible;
- Be sure to take into account the direction of the wind so that the kennel is not blown;
- The place should be well lit, but located next to a shady area, it is there that the dog will rest from the heat;
- It is better to arrange housing for the pet further from the pond, pool, well, otherwise excess moisture can accumulate under the kennel, which will bring discomfort to the animal;
- It is also better not to place the booth next to flower beds and flower beds, the animal can unintentionally harm them.
Dimensions of the dog house
At the first stage of construction of housing for a dog, you need to decide on its size. They depend on the size of the pet. An animal can be one of 3 types.
Practice has shown that the following parameters are suitable for each type of dog:
- The size of the kennel for small dogs such as pug, terrier or spaniel, width 55 cm, length 70 cm and height 60 cm. The size of the manhole is 30 by 40 cm.
- For animals of medium size, such as a Shar Pei, Foxhound or Basset Hound, the size of the booth is 75 cm wide, 120 cm long and 80 cm high. The size of the manhole is 35 by 50 cm.
- Booth for dogs of large breeds, which include Alabai, Mountain Dog or Dalmatian, width 100 cm, length 140 cm and height 95 cm; Manhole size 40-50 by 60 cm.
The dimensions of the booth vary depending on the actual dimensions of the animal. Some animals have non-standard dimensions, in such cases it is better to carry out individual measurements. The pet’s ribcage should pass freely into the hole. The Alabai breed is distinguished by its large size. The dimensions and drawing of the booth for the alabai are determined only after taking measurements from the animal.
When making calculations for the manhole, it is worth measuring the dog’s chest and adding 5-8 cm. The height of the manhole is equal to a value that is less than 5 cm of the animal’s height at the withers. The maximum depth and vertical dimension make it 5. 8 cm more than the height of the dog at the withers.
DIY dog booth
Before starting a dog, you should think about where the animal will live. A self-built dog kennel will delight your friend. You can make a comfortable home for a pet from the simplest materials at hand in a short time. It is necessary to choose the right size of dwellings for the dog so that the animal feels comfortable and protected at any time of the year, be it autumn, winter or hot summer. A house for a pet, made with his own hands, will become an additional decoration of the site.
Step-by-step instructions for making a dog booth with your own hands
First, make a drawing. The dimensions in the drawing must correspond to the actual dimensions of the kennel. For step-by-step instructions, a drawing of a booth for a dachshund or jagdterrier was selected. These breeds belong to a small group. For medium and large breeds, the sizes are increased according to the table.
- The base is 90 by 70 cm in size.Take 2 beams 70 cm long and fix boards 90 cm long on them.
- Niche for insulation. You need a bar with a section of 50 by 50 cm.Cut it into 2 bars 90 cm long and two 60 cm long. The bars are fixed on the base.
- Do-it-yourself doghouse insulation. Cut out the insulation and fasten it tightly to the base.
- Floor. The comfort of the animal depends on its quality. You will need boards 90 cm long, they are fixed with self-tapping screws at the base.
- Side walls. We need two side walls. For walls, the dimensions of the board are 65 and the beams are 40 cm.The walls are fixed at the base of the floor with corners and self-tapping screws.
- Front and back walls. You will need boards 70 cm long and 40 cm long bars. Leave a place for a manhole on the front wall. The animal must pass freely through the hole.
- Fixing all walls.
- Insulation on the booth walls.
- Internal wall cladding.
- Securing the roof to the walls.
- Fastening the bars under the insulation.
- Align the insulation well and fix it at the base.
- Sheathing the ends of the roof with boards. A gable roof is made with a slope so that the water glass when it rains. The gable roof is suitable for large dog breeds. It will increase the internal dimensions of the booth for Malamute, Alabai, Bulldog, Rottweiler or other breed.
- Roof insulation boarding.
- Roof covering with roofing material.
After completing the work, carefully inspect the box and remove all unnecessary from it. There should be no sharp or stabbing objects, especially if the kennel is for a puppy, and not for an adult dog.
Dog booth with a canopy
The canopy booth is suitable for large watchdogs. The canopy protects the animal from rain and snow, but at the same time will allow him to calmly guard the area. The area under the canopy should be the same size as the kennel itself or slightly larger so that the entire body of the animal can fit on it.
A shelter with a canopy is sure to please the following dog breeds:
- St. Bernard.
When making a drawing of a booth for a shepherd dog or any other large breed, be sure to take into account the canopy.
Unusual booths for dogs
If the site on which the booth will be located is made in the same style, everything is thought out and decorated in accordance with all the rules of landscape design, then an ordinary kennel for a pet will not work. Making a dog booth with your own hands, you can turn on the imagination to come up with something unusual. You can build a structure of an unusual shape or decorate a perfect ordinary house. Any materials at hand are suitable for decoration, you can also make wood carvings.
When decorating a house for an animal, you should also take into account the individual characteristics of the pet and its character. A do-it-yourself booth for a Rottweiler, Great Dane, Bulldog, Boxer or Pit Bull should match the fighting qualities of these breeds. Don’t make ridiculous decorations like flowers or funny faces. For such serious breeds, jewelry in a strict style is suitable, emphasizing the character of the breed.
Original dog kennels are a trend for several seasons. If you try, you can make a comfortable and unusual house to the envy of all neighbors.
Do-it-yourself doghouse: two photo reports
When a dog appears in the house, the question of housing immediately arises: somewhere she must sleep and hide from the rain. Not everyone wants and can keep them in the house, because the kennel is required. A do-it-yourself dog booth is built, even without skills, in one day. Nothing complicated, but there are features.
When building a booth, you need to focus on the size of the dog
The roof in the doghouse can be pitched or gable. Shed, preferable: not very large animals like to sit / lie on it. So they can control a large area.
Another point: since there is no heating in the booth, in winter the air in it is heated by the heat generated by the body. The larger the volume, the longer the kennel will warm up. The gable roof on the kennel just significantly increases this volume, without bringing any other benefit. If you want your dog to feel good, use a pitched roof.
If you don’t like it at all in terms of aesthetics, make a ceiling, and the roof itself is already on top. over, it is advisable to make it removable or folding. on the hinges. So it will be more convenient to carry out periodic cleaning and disinfection: organic residues are clogged in the cracks, in which fleas breed. It is from them that you will have to process the kennel from time to time.
A dog booth must have a raised floor. To do this, make legs at least a few centimeters high or knock down the frame, on which floor boards are laid directly.
In general, if possible, dogs prefer to spend time outdoors. Therefore, it would be nice to make a canopy in front of the doghouse or on the side of it. And to be able to sit / lie under it. make a flooring.
I see everything, I hear everything))
In this booth, not a folding roof, but a front wall, which is also convenient when processing.
How wide is the hole
There are recommendations regarding the width of the access hole. It is determined based on the width of the dog’s chest. Measure, add 5 cm, you get the width of the hole. The height depends on the height of the withers: you also add 5 cm to the measured value.For the puppy, first make a small hole. a little more than required, as it grows up.
The hole in the doghouse is not located in the center, but closer to one of the walls. With this structure, the dog will be able to hide from precipitation or wind behind a solid wall, curling up in a protected part. It is often suggested to divide the booth with a partition, making a kind of “vestibule” and sleeping area. But hiding in a fenced-off compartment, the dog cannot control what is happening in the entrusted territory. Many conscientious watchmen really do not like to go there. Some, even in the most severe frosts, lie opposite the entrance, not wanting to leave the post. So, the option shown in the photo with an offset access hole is optimal.
Another point: at the entrance to the doghouse there should be a nut 10-15 cm high.It protects the dog lying in front of the entrance from wind and precipitation, prevents snow and rain from clogging inside.
It is better to make a folding roof
Do-it-yourself insulated dog booth
If we talk about drawings, the animal does not need any “bells and whistles” and too large sizes. For them, this is a burrow, but it cannot be large, by definition, and it is difficult to heat excess volumes in winter. The booth was made with two windproof walls and a small canopy.
Ready kennel for a dog
First, they made two pallets in size with supports on four square beams, then they connected them together. It turned out a podium, on which the floor boards were fixed. Legs in the design are desirable. the floor will not get wet.
Ready floor for the booth
Bars were fixed in the corners. At the junction, there were six pieces: four for the kennel itself, two in front for the windproof walls. First, they made the inner lining, to which they fixed 7 cm of foam, then sheathed it outside. To prevent water from flowing into the walls between the boards, the gap was closed from above with a bar of suitable width.
Walls in the booth with insulation
When sheathing a wall, to which the windproof wall is adjacent, the boards were used whole. so the structure is more rigid.
Laz and insulated removable roof
The longest time we fiddled with the roof. I didn’t want to make it completely flat, so they made a strictly insulated shield, which was attached to a slightly rounded roof made of type-setting rails. At least it turned out without a slope, but due to the sloping shape, the water flows off without problems. Since it was still not possible to make hermetically sealed, a film was placed under the slats.
We decide on the size and design
The correct booth for a dog is not built just like that: you need to know what size it is required, where and what size to make a hole, what is better to make and how to insulate.
First of all, they are determined with the size of the dog kennel. The easiest way is to focus on the size of your dog. The height of the dog booth should be 5-6 cm higher than the pet, in width / depth it is approximately equal to the length of the body, plus 10-20 cm in length to be able to stretch the legs. In general, dog handlers have recommendations for the size of doghouses. They recommend making booths depending on the size of the breed. The data are presented in the table (width / length / height of the doghouse are given in centimeters):
|For large dogs (kennels for Alabai, shepherd dogs)||120||100||100|
|Medium breeds (husky, husky, labrador)||100||80||100|
If your pet does not exceed the average size of its breed, you should not increase the booth: it will be difficult for him to warm it up in winter. Please note that these are internal dimensions, if sheathing is planned, the dimensions are increased by the thickness of the walls.
Sizing a dog kennel
What to build and what to insulate
Most often, a doghouse is made of wood or wood materials. Wood is preferable. it keeps it cool in summer and warm in winter. In it, the dog will quite comfortably endure the winter, if the boards are fitted tightly, there are no cracks, even with a single wall the wooden booth is warm. So that, by the way, the dog booth turns out without gaps, they use an edged board, sometimes even grooved.
Concrete and brick booths are not the best choice: they conduct heat well, it is too hot in summer, and very cold in winter. That is why dogs often prefer to spend the night in the open, and not in a brick kennel.
If the wood is too expensive, use boards for the frame, and everything else can be made from OSB, fiberboard, plywood. If you use a sheet of wood material, you may need two layers of it: it is still much thinner than wood and, due to the presence of a binder, has better thermal conductivity (it retains heat worse). Therefore, in this case, you can think about insulating the booth for the winter.
Plywood doghouse: an example of insulation
You can insulate with any suitable material. You can use the leftovers from the construction of a house, a summer residence, a bath. It can be rock wool (like in the photo), foam or other material. When insulating with foam, do not overdo it: it does not allow air to pass through, and if you hang a curtain on the manhole, the dog will stop sitting in the booth: there will not be enough air for it. Therefore, either leave small gaps or provide some kind of air intake channel.
If we are to insulate, then the floor and the roof too. They are also made double, laying with the same insulation. Too large a layer of insulation should not be done: the dog itself can warm up quite well, besides, it has a decent fur coat. And for her, it is worse. a frequent sharp change in temperature than constant cold. If you want the dog to be warm, fill the kennel with straw for the winter: they will trample it where necessary, and throw away the excess. You need to change such a bedding twice per winter.
For the winter, a dense fabric cut into rather thick strips is nailed over the manhole. Two strips cut into noodles are fixed with a shift of the cuts. So it turns out that the wind does not blow into the dog booth, and the entrance / exit is free. But some dogs do not immediately get used to this innovation and sometimes refuse to go inside.
The outside of the booths can be painted, but not from the inside. The canopy and the wall from the wind (preferably one deaf) are treated with antiseptics. There is no point in painting them. The main thing is to make the roof without cracks, so that it does not flow inside and does not blow out.
A firewood shed or woodshed is easy to do with your own hands. How to read here.
A booth from a bar for Alabai from a bar
Let’s say right away that the doghouse was built from materials left after the construction of the bath. She will also be placed next to it, because in appearance it should resemble the bath itself.
The basis of this booth for a dog was a drawing with the dimensions of the booth for an alabai. But since the dog is not an Alabai, the dimensions were made more modest. Corrections were made to the design: a window was made in the side wall for viewing, and a door for cleaning was made at the back.
Barn from a bar for a large dog
First, they built and painted a platform. from the remains of logs, which were cut and put together. Then the actual assembly of the doghouse began. First, they planed and sawed in the workshop, and the finished structure was taken out and installed in place. near the bathhouse.
The first crown was placed whole. It forms the sill and supports the entire structure. Then the timber was cut according to the scheme. Considering that work experience had already been (the bathhouse was built), the work proceeded quickly.
The first two crowns are folded
Since it was supposed to make the roof a “house”, as in the bathhouse next to it, to keep the dog warm, they made a ceiling. A sheet of plywood was used for it. A dowel was made in the timber, on which a sheet of thick plywood cut to size was laid. Then they assembled and installed roof shields.
Dog kennel ceiling
They were not assembled according to the rules. the rafter system was not made. Since the roof is decorative, they assembled the shields, chipped them with the remains of soft tiles (they also remained from the construction of the baths), then they were connected and sheathed with gables.
The roof was not done according to the rules
Then the gables were sheathed with boards. The cracks were covered with boards. The dog house is ready. Handmade in half a day.
We are not quite Alabai and not Caucasian, but also not a very small dog
Such a structure for a dog of this size will still be large. This kennel is designed for larger dogs. The situation can only be saved by a partition installed inside, which reduces the width.
Another do-it-yourself dog booth is made of OSB, covered with a profiled sheet (insulation and inner lining are planned). The assembly process is filmed on.