home Dogs How to build a warm dog house

How to build a warm dog house

build, warm, house

Do-it-yourself booth with a vestibule

To make the dog booth more comfortable, you can build it with a vestibule. Such a dwelling for a dog will consist of two sections:

  • the distant part, which is a sleeping place;
  • near part for increased protection against cold and draft.

The compartments are separated from each other by means of an insulated partition, in which the access hole is located.

It is not so difficult to make a kennel for a dog, but during its construction it is not recommended to make a large sleeping place, since almost all dogs curl up while sleeping. In this case, it is necessary to provide for the opportunity for the animal to stretch freely in the vestibule when it rests in this place. Therefore, the size of such a part of the house should correspond to the height of the dog.

Booth for a dog with a vestibule. Dimensions and drawing

The assembly of the structure with a vestibule takes place in the same way as for other booths. A distinctive feature of such a house is the partition between the two sections of the dog’s dwelling. It is created from bars with a section of 40×40 mm, plywood, insulation material and self-tapping screws. First, a frame is made, the dimensions of which correspond to the width and height of the booth room. Then plywood is nailed to it, on the one hand. Then insulation is laid in it, on top of which another sheet of plywood is fixed.

How to build dog house for winter

In order for the partition to be easily removed, the need to take two slats from wood and select longitudinal grooves in them using a cutter. Their width should be equal to the thickness of the partition. After that, the slats are fixed on the walls of the booth. After that, it remains to insert the partition into the created grooves.

Tools and materials for work

In order not to be distracted during the construction process, everything you need must be prepared in advance:

  • dry timber 100×100 and 100×50 mm;
  • edged board 25 mm thick;
  • lining for cladding;
  • plywood or chipboard sheet;
  • bars 40×40 mm;
  • Styrofoam;
  • roofing material;
  • glassine;
  • antiseptic impregnation;
  • sand;
  • galvanized nails;
  • door hinges;
  • hammer.

Boards and blocks should be thoroughly cleaned before assembly, otherwise the dog may splinter its paws. But it is better to treat wood with impregnation at the end of the work, and only from the outside: extraneous odors irritate the animals, so the dog may refuse to enter the booth.

Booth with a vestibule

To make the dog’s home more comfortable, you can build a kennel with a vestibule. This is a structure consisting of two compartments: the far one is a sleeping place, and the near one protects from drafts and cold. They are separated by an insulated partition with a manhole.

Floor insulation

The photo shows a variant of foam insulation, which is placed between the bars and sewn up with boards

The planked frame is laid so that the bars are on top. They line the inner surface with glassine, attach it with staple staples, and then cut the foam to the size of the frame and place it tightly between the beams. The height of the insulation should correspond to the height of the bars. From above, the foam is covered with another layer of glassine and the finished floor is filled.

How to make a warm kennel for a dog: drawings, photos

Do-it-yourself insulated capital dog booth: drawings and dimensions. Step-by-step photo instructions for making a doghouse from boards and insulation.

If you decide to have a dog, a loyal friend and a reliable guardian for your home, then, first of all, you need to take care of a warm home for your pet. In this article we will look at detailed instructions on how to make a warm capital kennel for your dog.

google_ad_client = “ca-pub-1974473278197966”; google_ad_slot = “3501064932”; google_ad_width = 580; google_ad_height = 400; “

First, you need to decide on the size of the booth, which in turn depends on the size of the pet. The booth should not be large, because the dog will not be able to warm up well in a large kennel, the optimal size of the inside of the booth should be such that the dog can freely turn around in the booth, the height of the booth is equal to the height of the dog with his head raised.

Optimal booth sizes for certain types of dogs.

READ  Neighboring dogs interfere with sleep where to go

What is the best way to make a doghouse? Of course, made of wood, this is a natural material that does not contain harmful substances and retains heat well.

To make an insulated booth, you will need a beam, boards and insulation. You can use foam or mineral wool as insulation. You can use nails to fasten the boards, but self-tapping screws are more reliable.

Step-by-step production of a warm booth for a dog: drawings, diagram, photo.

Consider the process of making a booth step by step with drawings.

We saw off two bars 70 cm long and fasten boards on them with screws, the length of the boards is 90 cm.As a result, we get the base of the booth measuring 90 x 70 cm.

We need a beam with a section of 50 x 50 mm. We saw it into bars, two bars of 90 cm and two bars of 60 cm.Fix the bars to the base.

Cut out the insulation and lay it tightly on the base. If you use mineral wool, then it must be wrapped on both sides with a vapor barrier, otherwise the wool will eventually pull moisture and lose its thermal insulation properties. No vapor barrier is required for Styrofoam and Styrofoam.

We need boards 90 cm long, sheathed insulation with boards, fasten the boards with self-tapping screws to the timber.

Now we need to make two side walls, we use boards 65 cm long and 40 cm bars.Fix the walls to the floor using metal corners and self-tapping screws, as an option, you can first fix it at the bottom of each wall along a horizontal bar, then screw the bars to the floor with self-tapping screws. the distance between the walls is 70 cm.

We will make the front and rear walls of the doghouse, use bars 40 cm long and 70 cm boards.In the front wall we make an entrance to the booth, the size of the hole should be sufficient for the dog to freely crawl through it.

STEP. We fasten all the walls of the booth together with self-tapping screws.

STEP. We put insulation on the walls of the booth (unforgettable about the vapor barrier for mineral wool).

STEP. The roof of the booth. We fasten the roof boards to the walls.

STEP. We sheathe the ends of the roof of the booth with boards. Since the roof of our booth is single-pitched, it is necessary to provide a slight slope towards the rear wall to drain water from the roof.

STEP. We cover the roof insulation with boards.

Now the roof needs to be covered with any covering material, you can use slate, roofing material, bituminous tiles or corrugated board.

Where is the best place to install a dog kennel?

The booth must be installed in the yard of the house so that the dog has a good view of the yard and the entrance gate, but at the same time, during the scorching heat, the booth should be in the shade of buildings, a fence or a tree. In winter, do not forget about the dog bedding, the booth should be half filled with hay or straw to make it easier for the dog to warm up.

I recommend watching an interesting video of making a doghouse.

How to make a kennel for a dog with your own hands. drawings, dimensions of the kennel

Do-it-yourself insulated capital dog booth: drawings and dimensions. Step-by-step photo instructions for making a doghouse from boards and insulation.

If you decide to have a dog, a loyal friend and a reliable guard for your home, then, first of all, you need to take care of a warm home for your pet. In this article, we.

How to make a warm kennel for a dog: drawings, photos

Do-it-yourself insulated capital dog booth: drawings and dimensions. Step-by-step photo instructions for making a doghouse from boards and insulation.

If you decide to have a dog, a loyal friend and a reliable guard for your home, then, first of all, you need to take care of a warm home for your pet. In this article we will look at detailed instructions on how to make a warm capital kennel for your dog.

First, you need to decide on the size of the booth, which in turn depends on the size of the pet. The booth should not be large, because the dog will not be able to warm up well in a large kennel, the optimal size of the inside of the booth should be such that the dog can freely turn around in the booth, the height of the booth is equal to the height of the dog with his head raised.

READ  Fleas in a dog how to relieve itching

Optimal booth sizes for certain types of dogs.

What is the best way to make a doghouse? Of course, made of wood, this is a natural material that does not contain harmful substances and retains heat well.

To make an insulated booth, you will need a beam, boards and insulation. You can use foam or mineral wool as insulation. You can use nails to fasten the boards, but self-tapping screws are more reliable.

Step-by-step production of a warm booth for a dog: drawings, diagram, photo.

Consider the process of making a booth step by step with drawings.

We saw off two bars 70 cm long and fasten boards on them with screws, the length of the boards is 90 cm.As a result, we get the base of the booth measuring 90 x 70 cm.

We need a beam with a section of 50 x 50 mm. We saw it into bars, two bars of 90 cm and two bars of 60 cm.Fix the bars to the base.

Cut out the insulation and lay it tightly on the base. If you use mineral wool, then it must be wrapped on both sides with a vapor barrier, otherwise the wool will eventually pull moisture and lose its thermal insulation properties. No vapor barrier is required for Styrofoam and Styrofoam.

We need boards 90 cm long, sheathed insulation with boards, fasten the boards with self-tapping screws to the timber.

Now we need to make two side walls, we use boards 65 cm long and 40 cm bars.Fix the walls to the floor using metal corners and self-tapping screws, as an option, you can first fix it at the bottom of each wall along a horizontal bar, then screw the bars to the floor with self-tapping screws. the distance between the walls is 70 cm.

We will make the front and rear walls of the doghouse, use bars 40 cm long and 70 cm boards.In the front wall we make an entrance to the doghouse, the size of the hole should be sufficient for the dog to freely crawl into it.

STEP. We fasten all the walls of the booth together with self-tapping screws.

STEP. We put insulation on the walls of the booth (unforgettable about the vapor barrier for mineral wool).

STEP. The roof of the booth. We fasten the roof boards to the walls.

STEP. We sheathe the ends of the roof of the booth with boards. Since the roof of our booth is single-pitched, it is necessary to provide a slight slope towards the rear wall to drain water from the roof.

STEP. We cover the roof insulation with boards.

Now the roof needs to be covered with any covering material, you can use slate, roofing material, bituminous tiles or corrugated board.

DIY Insulated Dog House Build

Where is the best place to install a dog kennel?

The booth must be installed in the yard of the house so that the dog has a good view of the yard and the entrance gate, but at the same time, during the scorching heat, the booth should be in the shade of buildings, a fence or a tree. In winter, do not forget about the dog bedding, the booth should be half filled with hay or straw to make it easier for the dog to warm up.

I recommend watching an interesting video of making a doghouse.

Felt

The simplest and most inexpensive insulation that can be mounted in a matter of hours:

  • Cut elements of the required size with a clerical or construction knife;
  • Secure the material from the inside of the kennel with a stapler and staples.

The result is high-quality insulation with natural material that is not afraid of wind and frost. It is also considered an important point that this heat insulator has a high vapor permeability.

Material

The material deserves special attention, because the choice will determine how comfortable the dog will be. We recommend building a kennel out of wood. For the construction of the structure, larch or pine wood should be preferred. Pine material, subject to proper processing, can last up to 13 years. Larch lasts much longer, but it also costs more. Which of these two breeds to prefer depends on the financial capabilities and preferences of the owner.

READ  DIY House For A Decorative Rabbit

As for the roofing material, it is better to give preference to natural materials, such as tiles.

Roof

What kind of roof to install on the booth: single or gable, depends on the preferences of the owner. We will analyze the pros and cons of each option.

Warm for the winter

You understand that if the dog’s house is on the street. it needs to be made warm! How to insulate the booth? For the construction of a winter insulated kennel, among other materials, it is necessary to prepare a heater. The cheapest is foam.

How to make a warm kennel (with drawings):

  • The foundation for the kennel.
    Cut bars 5×5 cm into 2 pieces of 700 mm and two pieces of 900, the result will be a booth of 900×700 mm.
  • Niche for heat insulator.
    You will need 4 bars. 2 x 900 mm and 2 x 600 mm using self-tapping screws to fix them to the base.
  • Warming.
    Cut the insulation to size and put it between the blocks.
  • Floor arrangements.
    Cut boards 900 mm long and stuff them onto the frame from the outside of the kennel.

Floor frame with insulation Floor insulation
Side walls.
We equip the side walls. To do this, take boards with a length of 650 mm and bars of 400 mm, assemble a frame to which the boards are screwed. Install the walls and screw them to the floor at the corners.

  • Front and back walls.
    In the front wall, with the help of bars, we construct a manhole, and fasten it to the frame. Install the back wall last. Fasten the walls with self-tapping screws. Arrange insulation, cut to fit the walls.
    We sew up walls with insulation boards or plywood.
    Wall insulation with foam
  • Booth roof.
    Screw plywood to the walls and sew bars on it. Lay insulation. Sew up the roof insulation with boards. Install roofing material.
  • The construction is completed, it remains only to install the insulated structure in place.

    Photo of the booth insulated according to all the rules:

    Useful construction video

    What can and what can not be insulated?

    When choosing insulation, remember that your dog relies on his instincts. It is impossible to tell her that you cannot gnaw the rug, or you should not tear off the canopy covering the manhole.

    Consider several options for warming a dog booth for the winter, their pros and cons:

    • The first thing to remember is that the insulation must be closed on both sides, otherwise the dog will simply tear it apart;
    • if mineral wool is used for insulation, then perlite should be laid between the wall and the heat insulator. It will not only preserve the properties of cotton wool, which is able to absorb moisture and lose its properties, but also protect the dog’s respiratory tract from irritation;
    • the canopy should be chosen from a dense and durable material, otherwise your pet will quickly tear it;
    • if possible, the thermal insulation material should be natural.

    Improvised means

    But you can also insulate the structure with improvised materials, for example, old sweatshirts or a blanket. Warming will turn out to be no worse than with the above methods. The only downside is that this insulation is short-lived, and rodents can start in quilted jackets.

    Or just invite the cat : There is no time for disagreement in the cold!

    Electric heating

    It is possible to carry out forced insulation if wiring is carried out to the booth. A warm, heated booth (like a rug) has advantages:

    • the temperature in the kennel is constant, even in extreme cold;
    • electric heating dries the air in the structure, which is important.

    But there are also disadvantages that cannot be ignored:

    • The dog is an active and curious animal, and can get to the elements of electric heating. There is a danger of electric shock.
    • A short circuit may occur in case of constant dampness.
    • You can try and protect your dog from these troubles, but then the cost of the kennel will increase significantly.