home Birds How to make a large parrot cage

How to make a large parrot cage

What should be a cage for a large parrot

The dimensions of the bird cage depend on how much space is planned to be allocated for the bird’s dwelling. over, it should have dimensions close to the standards of 75x100x175 cm. Less. only if a large parrot has the opportunity to often fly around the room.

Very small dimensions are bad for the health of the pet. He will feel constrained, move a little, it will be uncomfortable for him to eat, to clean his feathers. It is difficult for a bird to delimit zones in a small dwelling. As a result, the parrot’s immunity will decrease. He will often get sick, eat poorly and communication skills will be at zero. It will be difficult to make friends with such a parrot and teach him to talk.

The best cage shape is rectangular with a flat roof surface. If the owner likes the round configuration, it must be borne in mind that the feathered in such a dwelling loses its bearings. He will not feel safe, as instinct forces him to hide in a corner in case of a threat.

make, large, parrot, cage

As a material for the cage, a metal is chosen that the parrot will not gnaw. Wooden cages are not suitable for birds, as they will constantly “gnaw” at them. Wood is an environmentally friendly material, but it absorbs odors and dampness. Washing such a cage is a big problem.

A flat roof is preferable in that it can accommodate a play area for the feathered.

Do-it-yourself parrot cage

For a feathered pet, the cage is his small apartment. She needs to be comfortable so that she wants to return to her home after a warm-up flight around the room. A sense of security is also important. This is possible when the cage is in the right place and equipped with everything you need.

Where to put a parrot cage

The best place for a parrot is where its owner will always be there. In modern conditions, this is complicated by the fact that there is a table with a computer next to it, near which it is not advisable to put a cage. TV, radio, speakers from the music center. these are sources of sounds that will annoy the bird.

The place should be bright, but not in direct sunlight. It is best if it will be a place against the wall near the window, but not in a draft. The walls give the parrot a sense of security. The bird will always know that on the one hand the threat should not be expected.

There is no place for a bird on the windowsill, even if the sun’s rays do not reach there. In winter, this is the coldest place; in the off-season, the temperature difference is most felt on the windowsills.

It is impossible to equip a place for a parrot next to a heating radiator, under an air conditioner, it will overheat or get burned.

If a fan turns on in the room, it is necessary to provide that the air wave does not reach the bird. I’ll scare enough to stay under such a stream for 15 minutes to catch a cold.

If the owner (hostess) spends most of the time in the kitchen, there is no need to put a parrot there. It is better to place it in another room so that the pet has a door leading to the kitchen in sight. Constantly breathing fumes from cooking food is very harmful for a bird, this can lead to the development of bronchopulmonary diseases.

Hanging the structure from the ceiling is not the best option. She may break down and fall. The parrot is unlikely to like the feeling of instability. Pallets have a habit of falling off at the most inopportune moment. To eliminate all these risks, the cage is placed on a solid stand.

It is cruel to put a dwelling with a parrot on the floor, since the parrot will have a limited viewing angle.

The stand for the cage must be strong and stable. If the cage turns over, the parrot will not die, but it will be very frightened. Stress negatively affects the health of birds. There were cases when talking parrots stopped pronouncing the learned words after being frightened.

How to make your own parrot cage?

A very good parrot cage is expensive. It can be made at home if you have the desire, materials and tools. Dimensions are made as needed for the interior. Homemade parrot cages can be equipped with utility bays.

How to properly equip a home for a parrot?

Everything necessary for the bird is placed in the feathered dwelling:

  • Separate feeders for dry and juicy feed, vitamins. Dry food (grains, granules) should always be present, fruits and vegetables are placed 2-3 times a day.
  • The drinking bowl must be automatic so that the water is not contaminated. Buy it ready-made or do it yourself.
  • Perches with a diameter of 15 mm for rest and for eating, near the feeders. The wood does not need to be polished, the roughness of the bird is needed for a strong grip.
  • There should be a lot of toys, but they should not interfere with the feathered owner of the home from moving around his apartment.
  • Bathing tank. Parrots splash with pleasure, especially in the heat. A deep metal cup is used as a pool, which is well fixed.
  • Mineral (chalk) stone. When the feathered one gnaws it, they put a new one. With a lack of calcium in the pet’s body, the beak, claws begin to exfoliate, and the joints weaken.

Sometimes parrots bring “treasures” to their home: things that they liked while walking around the apartment. This happens more often when the parrot has few toys, not enough attention is paid to it.

Tools and materials

Parrot cage net with 3 mm thick rods. It is necessary to find steel, but in no case galvanized, which has a destructive effect on the bird’s body.

  • Pallet sheet (wood, plastic, getinax, laminated moisture-resistant chipboard).
  • Bars for the base of the cage.
  • Wood for perches made of linden, birch, pear, apple, cherry. Do not conifers, lilacs and acacia, as they contain dangerous glycosides.
  • Metal scissors.
  • Hacksaw for wood.
  • Pliers.
  • Electric drill.
  • Nails (screws when it comes to plastic).

Step-by-step manufacturing instructions

Making a home for a feathered one is within the power of a master without experience. Step-by-step instructions provide for the manufacture of a pallet, frame, doors, perches and assembly of all structures:

  • The pallet is made first, all other structural elements will be repelled from it. A slab is cut out with a hacksaw and four bars of the desired size, which are nailed along the perimeter of the pallet. Nails are driven strictly outward. so that they do not stick out inside the cage.
  • Cut blanks from the mesh using metal scissors. It turns out 5 segments: 4 walls, 1 roof. When calculating the dimensions, it must be borne in mind that the edges of the canvases must end with open rods (for hitching). If you have a grinder, you can use it to cut canvases.
  • In the front part, slits are made for the door and the door itself. The edges must be even, without sharp rods and burrs.
  • Now the mesh needs to be assembled. To do this, they put them at an angle of 90 ℃ and twist the bare rods with pliers into a strong loop. In this case, the sharp edges should look outward, and not inside the future cell.
  • The next step is to make perches along the width of the mesh span. An incision is made at both ends of the crossbar, with which a perch is placed on the wire for fixing.

There are two ways to assemble a cage. Place the mesh frame on the pallet, and make notes under each rod. Drill holes, into which then insert the rods and bend them from the back. The second way is to attach the frame to the pallet using metal brackets.

A simple method to secure the door to the facade is with wire twists. They make a homemade heck or buy a ready-made one. So that the roof of the cage can be removed if necessary, it is fixed in several places with wire.

Training

A list of parts should be compiled, consisting of groups of elements, the size parameters and the purpose of which are the same.

  • Wooden components are sawn off from the workpiece in accordance with the specified dimensions. The sawing points are sanded to a smooth state. Eliminates the presence of wood chips and splinters.
  • The metal mesh is cut with metal scissors in accordance with the specified dimensions. It is unacceptable to leave open cells at the edges of the mesh fabric. Cutting points of mesh links are processed with sandpaper to eliminate the likelihood of injury during assembly and harm to the parrot.

Stacking parts according to the principle of grouping makes assembly easier and reduces the time spent on it.

The assembly of the structure is carried out on a modular basis. Walls, top and bottom parts are assembled separately. Wooden slats are interconnected in accordance with the drawing instructions. In order to avoid cracking the wood in the places where the self-tapping screws are screwed in, the boring hole is drilled using a drill, the diameter of which is half the diameter of the threaded part of the self-tapping screw.

In addition, a secret recess is drilled into which the head of the self-tapping screw sits. For this, a pen drill with a diameter equal to the diameter of the head is used. The nib drill allows for chipping-free drilling, as well as to ensure the taper of the sweat, which will ensure the quality of the self-tapping head fit in it.

The metal mesh is attached to the slats using finishing nails. Their advantage lies in the presence of a small head, softness of the material and the ability to control the working length. The nails are driven into the slats in such a way that, when bent, they can overlap the mesh rods at the point of their contact. The frequency of driving in nails will be optimal if they are driven in through 1-2 mesh links.

The assembled components are assembled into a single structure. Perforated metal corners are used as parts that strengthen the strength of the joints, which are screwed with screws of the appropriate length.

Self-tapping screws tend to gradually unscrew as a result of the wood’s susceptibility to expansion-contraction processes, due to its reaction to temperature changes and the degree of air humidity.

To eliminate this factor, to strengthen the strength and increase the durability of the joints, you need to dip the threaded part of each self-tapping screw into PVA glue before screwing in.

On one side of the cage, a frame should be equipped, providing for the installation of a door. It consists of two rack and pinion circuits. The outer contour is the base to which the door frame is attached.

The hinges holding the door on themselves must be outside. This can limit the bird’s ability to have access to iron parts.

The cage should be designed with a double bottom. The first is a metal mesh, and the second is fiberboard. When designing a cage, it is necessary to take into account the availability of access to the second bottom. This will allow regular cleaning of the cage.

Watch the video tutorial on how to make a do-it-yourself parrot for a parrot further.

Tools and materials

The list of materials directly depends on certain types of cage construction. Their differences from each other are reduced to the difference in the configuration of the case. Among the common types of cells are:

  • lattice with an all-metal body;
  • cellular all-metal;
  • lattice combined;
  • cellular combined;
  • plastic, wooden.

The all-metal body is a structure assembled from a metal mesh with a square mesh or lattice sheets, connected to each other by means of spot welding or other fastening materials.

The combo version of the case combines a wooden or plastic frame holding a lattice or mesh material on it. In this case, the mesh can be made of plastic, and the bars of the lattice can be made of wood.

The optimal variant of the cage design is a combined one. Its features allow you to assemble the fixture without unnecessary material costs using a minimum set of tools.

READ  Do-it-yourself bed for a large dog

To assemble the birdcage shown in the photo, you will need the following list of materials:

  • metal mesh with a square mesh, mesh size should not exceed 20 mm;
  • planed wooden slats, average parameters of slats 15×30 mm;
  • plywood or fiberboard up to 5 mm thick;
  • consumable metal products. self-tapping screws, finishing nails, hinges, perforated fastening angles, drills.

The mesh, which will be used as the main material for the walls of the cage, must have minimum dimensional characteristics. This will reduce the weight of the entire structure and facilitate the assembly process.

The size of the wooden battens is not fixed. As this material, you can use slats with different sizes. It is important to take into account the weight factor of the structure. The narrower and thinner the wood components, the less its final weight. It is undesirable to use unplaned wood. The presence of irregularities, splinters and wood dust can negatively affect the condition of the bird that will be kept in the cage.

For arranging the bottom of the structure, it is recommended to use fiberboard. This material has several advantages over plywood. At least one side of the fiberboard is covered with a water-repellent layer, which provides the best possible operation in these conditions, since the bottom of the cage is the final surface on which poultry droppings and other waste products of its vital activity fall.

Consumable metal products must correspond to the parameters of wooden materials. For example, self-tapping screws after screwing in should not protrude from the other side. The pitch of their thread should be selected taking into account the minimum risk of wood splitting at the time of screwing in. The width of the fastening metal corners must match the width of the wooden battens. It is unacceptable for the corners to protrude beyond the frame perimeter.

The values ​​of the diameters of the drills must correspond to two values: 1) the diameter of the head of the self-tapping screws, 2) the diameter of their threaded part, divided by 2.

In accordance with the names of the selected materials, a list of tools is prepared:

  • sawing devices for wood (hacksaw or jigsaw);
  • drill, screwdriver;
  • hammer;
  • scissors for metal;
  • medium grit emery sheet;
  • Phillips screwdriver;
  • measuring instruments (tape measure, ruler);
  • PVA glue;
  • other related names.

Requirements

The main criteria for the quality of a parrot cage. size, material and design.

The physiology of any bird is a set of biological characteristics that necessitate the absence of restrictions on freedom of movement. Some properties of their body indicate a dependence on constant physical activity. The size of the cell is calculated taking into account this fact.

Parrots are representatives of the genus of birds that are extremely sensitive to external factors. They easily succumb to diseases, it is difficult to survive molt and periods of physiological craving for reproduction. Along with this, one can note their exactingness to the materials from which the cage is made. Their environmental friendliness and safety are important.

The physical condition of the parrot directly depends on the design features of the dwelling. Some cages are supplemented to give the bird the ability to meet its energy needs and gain access to water and food. These additions include:

  • swing;
  • rotating wheels;
  • hanging hoops;
  • various toys and more.

The form and materials from which additional devices are made must also comply with environmental and safety standards.

There are various modifications of parrot cages that you can assemble with your own hands at home. Before assembly, you need to prepare the appropriate materials and tools.

Making a cage for a parrot with your own hands

The parrot is a bird of tropical origin. Distinctive features. motley plumage color, lively disposition and the ability to imitate human speech. This genus of birds is marked by a large number of subspecies.

In most regions of the world, it is used as an ornamental pet. For commercial purposes, it is bred and kept on specialized farms of an industrial and private nature.

Specific requirements are imposed on the characteristics of the feed and the conditions for keeping exotic poultry at home. A lattice cage is used as a home for a parrot and a means of isolating it from the environment. This device allows you to provide the proper conditions for a comfortable life, while maintaining the ability to communicate with the outside world, since parrots bred in captivity are extremely social.

There are various modifications of cages for a parrot, differing in the presence of certain functional capabilities. Some copies may cost 1,000. Along with them, budget models are supplied to the zoo market, which are available for the middle-level buyer. In addition, following the instructions, you can design a cage with your own hands, which will take into account the individual characteristics of a particular bird and save money.

Step-by-step instruction

In order to make a cage for a parrot with your own hands, detailed drawings are drawn up. They must indicate the dimensions of all constituent parts of the structure. The availability of drawings will allow preparation of parts and subsequent assembly with maximum accuracy, which will ensure acceptable product quality and its proper appearance.

Advice

The construction of a parrot cage is not limited to assembling the main frame. For a full life, the bird needs devices that provide food and water.

To equip these devices, you can use the properties of the metal mesh from which the walls of the cage are made. Tanks for water or food are suspended from the mesh cells using homemade hooks made of strong wire.

The container supplying water. the drinker. must be located outside the cage. Inside there is only a stand in which liquid accumulates.

For a comfortable stay of a parrot in a cage, you need to equip a perch. To do this, you can use a homemade crossbar, which lies with its edges in the mesh cells located on opposite walls. In most cases, there is no need to permanently fix the perch. It is periodically removed to clean the droppings.

The simplest accessory in a parrot cage is a swing. They are made from two pieces of steel wire. Loops are bent on both sides of each segment. A wooden crossbar is inserted into one pair of loops, on which the bird will sit, and the other pair of loops is fixed on the ceiling of the cage while maintaining the possibility of pendulum movement.

The homemade parrot cage is extremely easy to assemble. Doesn’t require any special tools or rare materials. Its independent production allows taking into account the characteristics of the room in which it will be installed, and the characteristics of a particular bird.

How to choose or make a do-it-yourself parrot cage

For several decades, parrots of various breeds have remained one of the most popular pets. However, these bright and beautiful birds did not always live in captivity, so they should not bring any inconvenience to the new pet at home.

Before choosing a new home for a parrot, you should familiarize yourself with all the varieties and features of the cells.

At home, the parrot, first of all, loses not only freedom of choice, but also becomes constrained in movement. For this reason, a caring owner must provide him with the ability to constantly move and change locations.

A spacious cage with a large number of perches and areas for practicing and playing will be ideal for the bird. If the parrot sits at the bottom of the cage too often, it is worth considering whether it has enough room to move.

Building Xlarge parrot cage aviary (macaw) #5

The cage should be large enough so that your pets can move around it normally, spread and flap their wings.

Correct cage placement

Having bought a cage, you need to choose the right place where it will be located and create the best environment for the parrot to live and communicate. If there are several birds in the same room, they should be located at a sufficient distance from each other.

The cage is placed so that each individual has a personal space. If limited, many species of parrots, often stressed by their nature, will feel unwell. over, representatives of the Grays may demonstrate inappropriate behavior if they are in a room with other parrots.

The parrot cage is best placed in a place often visited by the owners. This will make your pet feel protected as a family member.

In addition, the owners will be able to adjust the pet’s behavior if necessary. To make your pet’s life comfortable, cover his house with a thick cloth at night.

You should not choose places with a large view for the bird, as this can make it feel insecure. It is worth considering the peculiarities of the character of a particular breed of parrot. So, some individuals will feel great in a cage placed in front of a window, but for the rest, such a location will be unacceptable.

Types of parrot houses

When choosing a cage for a parrot, it is important to pay attention to its type and correctly organize the future location. A house for a bird should provide it not only with physical safety, but also with a sense of comfort during the absence of the owner.

Cages for large parrots, as well as for smaller individuals, should not be floor-standing, because in natural conditions these birds never make their nests on the ground. For this reason, it is worth choosing a cage equipped with a bottom located at least 35 centimeters from the floor.

An important element for the parrot is the playground, which occupies the upper space of the cage. There the bird will be able not only to study, but also to take a nap.

When choosing a home, you need to consider the following factors:

  • species, size and life experience of individuals;
  • the time the parrots will spend in the cage;
  • characteristic features of birds.

So, in large individuals such as blue-headed parrots, cockatoo, macaws and Amazons during puberty there are outbursts of aggression, their cage should not contain perches located at the level of human eyes. Other species of long-winged parrots almost never exhibit this behavior.

What should be in a pet parrot’s cage?

To make a cage a real home for a parrot, you need to add interesting toys and gadgets to it. The parrot must have:

  • various perches;
  • spirals;
  • swing;
  • perches;
  • feeders installed at different levels;
  • additional seating.

Parrots are very intelligent and playful birds that do not like boredom. Therefore, entertainment is necessary in the cage: rings, laces, a bell, etc.

It’s worth rotating and changing these helpful additions each week. It is best to place the cage on a hill so that the parrot is at eye level. Many manufacturers make cages with special adjustable stands. A cage for large parrots must have wheels for easy transportation if necessary.

How to choose the right shape and size of the cage?

If the future pet is blue-headed or budgerigars, the cage for them should be at least sixty centimeters. Medium-sized individuals and Amazons will feel great in houses that are more than eighty centimeters. The cage for large parrots should not be less than one meter.

Large parrots have strong beaks and well-developed intelligence. Therefore, the cages should be with solid metal rods. Any wooden parts can be gnawed by them.

Birds are perfectly oriented in space and are aware of the amount of free space, on which their behavior depends. For any parrot, you should choose a house, the horizontal size of which will exceed the vertical one, because these birds move strictly in the horizontal plane.

Instructions for creating a cage for a parrot with your own hands

First of all, you need to correctly select the size of the cage and make a detailed sketch with all measurements. A cage for budgies can be small, but you shouldn’t save on materials and neglect the height and width of the new bird house, because parrots in a cage should feel comfortable.

A standard cell consists of the following elements:

  • pallet. a small box that can be made of fiberboard and slats, while the sides of the pallet must be high enough;
  • the frame, which is a mesh, curved in the shape of a cube and fixed to the frame;
  • roofs.

To make a house for your pet yourself, you will need to purchase wire, corners, a metal profile, nails and screws. A homemade parrot cage should be made only of their environmentally friendly materials that are not hazardous to the health of the bird.

Oak or ash is used as wooden blocks. This will significantly increase the life of the cage, even with frequent contact with water. To make the cage look beautiful, it can be coated with modern eco-friendly paint.

First you need to make the frames, which is not at all difficult, but special attention should be paid to their strength. Each frame must consist of four blanks.

Then the side parts are created from the metal profile. The longitudinal part of the side walls must be bent at right angles and the lower and upper parts must be attached to them. The frame components will be fastened with self-tapping screws.

Knowing the size of the frames, you will need to cut off the required amount of mesh. Then it is adjusted to the edges of the profile.
By attaching a mesh to the frame, the points of intersection of the ends of the wire and the frame are marked. Holes are drilled on them equal to the diameter of the mesh wire.

READ  What tree branches can Corella parrots have?

When the parrot cage is almost ready, you need to make small hooks to which additional elements will be attached: drinkers, perches and feeders.

To make it easier to keep the cage clean, you can make a pull-out tray. To do this, it is enough to make a frame from a profile and attach a galvanized sheet to it. An important element of the cage is the door. This can be done by cutting a hole in the mesh. The door should be small and close from top to bottom. You can also make a lock to it yourself.

Only after all the necessary accessories for the parrot are installed in the cage, the new pet can be introduced to a cozy home.

Suitable place for a cell in an apartment

A city apartment or even a private house is not a natural habitat for a parrot. In such conditions, dangers lie in wait for a bird literally at every corner. That is why it is very important not only to choose the right cage, but also to correctly determine the place where it will be located. Not suitable for birdhouse installation:

  • remote rooms where people rarely enter;
  • a kitchen where food is prepared and there is a lot of steam (evaporation from Teflon dishes is especially dangerous for poultry);
  • rooms where it is often too noisy, especially if such noise occurs unexpectedly (for example, music or “loud” electrical appliances turn on abruptly);
  • places under the influence of direct electromagnetic and radio waves (near electrical appliances, personal computers, WiFi routers, etc.);
  • areas in the immediate vicinity of heating devices. dry and warm air adversely affects feathers;
  • blown places. parrots can tolerate cold air, but they instantly begin to hurt from a draft and may even die;
  • window sill or close proximity to the window. in this place it is especially cold in winter and too hot in summer, when the window is open, there is a draft, and the noise coming from the street will scare the parrot.

Corella is a very sociable bird, even among sociable parrots, so it should be able to observe the events taking place around, listen to human voices and other sounds and take part in all this as much as possible. Do not place the cage in the middle of the room: if one or two sides of the dwelling are firmly pressed against the wall, its occupant will feel much more protected and less vulnerable. The fact is that a locked bird cannot hide from potential danger, as it does in the wild, which means that it should be able to retire from prying eyes in a securely protected corner if something scares it.

Dimensions (edit)

The cockatiel cage must match both the size and character of the parrot.

The body length of an adult can reach 33 cm, the wingspan is 38 cm, which is approximately twice the average size of the budgerigar.

In addition, in the wild, cockatiels never settle in tropical thickets, preferring an open space to a dense forest. It is for this reason that for this species of parrots it is important not just a spacious, but a spacious dwelling (ornithologists note that it is actually better to keep these birds in aviaries, and not in cages, but in any case, you need to strive for the largest possible size of the dwelling, especially if we are talking about several birds).

Experts talk about the following minimum cell sizes:

  • length. 60 cm;
  • width. 40 cm;
  • height. 70 cm.

The main parameter in the cage is not the height, but the length, because the bird does not fly from top to bottom. Lack of horizontal space can cause the cockatiel to injure its luxurious wings or break its tail.

The form

As you know, parrot cages can have a round, square or rectangular base. The cylindrical shape of the dwelling looks very beautiful, but in this case the tastes of the owner and his pet do not coincide at all. In the absence of corners, parrots feel uncomfortable, disoriented and nervous. In addition, turning its paws along the bent rods, the bird will constantly slide off, which is fraught with injuries.

How to choose the right cage for cockatiel parrots

In order to determine the choice of a cage, it is necessary to obtain at least the most general information about the bird for which it is intended.

Manufacturing steps

The process of making a cage step by step involves the following actions:

  • We start with a drawing. we determine on paper the initial dimensions of the details of the future cage. pallet, walls, roof.
  • If a ready-made pallet is not used, at the initial stage it is necessary to make it. Cut a rectangle of the required length from wood or plywood using a jigsaw or saw, three side pallet parts (one long and two short, at least 10 cm wide), as well as three strips for installing the mesh. the same length as the sides and height 2–3 cm. The fourth long side bar should be narrower than the other three so that the cage can be cleaned.
  • Using glue, we fasten the base of the pallet with three sides (the fourth will be installed at the last stage). We glue a strip to install the mesh to each inner side of the sides.
  • Cut out the side racks. We need eight boards of a given height, about 6 cm wide.
  • We glue the racks in pairs in the shape of the letter “L”.
  • Using nippers, we cut out four walls from the mesh for the future cage.
  • With a pencil or pen, mark the holes on the side walls in accordance with the mesh cells.
  • We arm ourselves with a drill and drill holes according to the prepared markings.
  • We insert the mesh rods into the prepared holes on both sides. We carry out in this way two long walls.
  • We glue the side walls into the base of the pallet.
  • Using a hammer and nails, we nail two horizontal strips to the top of the long walls (the end of the mesh should remain outside).
  • We nail the remaining fourth part of the pallet in such a way that its upper part coincides with the other three sides, and the lower one is 3-4 cm above the bottom (it will be convenient to remove debris through the gap formed from the cage).
  • We fix the side walls with horizontal strips from the outside of the pallet.
  • Insert the two remaining mesh fragments (short cage walls).
  • We fix the mesh from the inside of the cage with the side planks using nails.
  • Moving on to the design of the ceiling. We bend the protruding edges of the long walls of the mesh to the sides and fix them on the pre-nailed horizontal planks using a construction stapler.
  • We nail three transverse ones to the long side strips of the ceiling. two along the edges of the cage and one in the center.
  • We bend and fix with a construction stapler the upper ends of the mesh on the two remaining short walls.
  • We are starting to manufacture the upper door. It will occupy one half of the ceiling. Cut out a fragment of the mesh of the required size with pliers and attach its ends with a construction stapler to two wooden planks (they should be located on the short sides of the door).
  • We attach a furniture hinge to one of the planks.
  • Using a screwdriver, we attach the second half of the hinge to the prepared opening on the roof of the cage, thus installing the door.
  • It remains to drown out the second half of the roof with a mesh. we cut out the necessary fragment of the mesh and attach it around the perimeter to the ceiling of the cage using a construction stapler.
  • The door on the ceiling is for the owner. Using this hole, you can install and change perches and other accessories inside the cage. And the parrot needs a visible and understandable door on the wall. It can be made from the same mesh by first cutting out the required hole in the wall using pliers and inserting the finished door into it (the easiest way to fix it is by making eyelets from the mesh rods and bending them accordingly).
  • As a final step, we make a pull-out pallet. For this, a fiberboard sheet is suitable, and to make it convenient to remove it, you can fix a transverse bar (profile) on one of its sides. She will also close the lower gap between the pallet and the net, preventing the parrot from trying to get out.

Accessories for equipping the cage

Since even the most attentive owner cannot spend all the time with his feathered friend, care must be taken that the bird can entertain itself, being alone.

In order to prevent the water in the cage from drying out and contaminated with droppings, food residues and other debris, it is better to purchase an automatic drinker made of organic or ordinary glass or plastic. In such a container, water retains its freshness for a long time. When using open drinking bowls, their contents must be constantly monitored and the water changed daily, and preferably even twice a day.

When filling the drinking bowl, you should take care that the water is at room temperature, since cold liquid can lead to digestive upset in the parrot, and a warm one will not give him pleasure and will not quench his thirst. It is also better not to use tap water, the best option is bottled water for baby food or just purified water.

The next accessory worth buying for your pet is a bathtub. It should not be kept in a cage all the time, but at least once a week, especially in the warm season, the bird should be given the opportunity to take a water procedure. At the end of the bath, the bath should be immediately removed so that the bird does not drink dirty water and does not get sick.

Of course, the birdcage must be equipped with various perches and perches. In the case of a cockatiel, there should be at least two. They should be placed at different heights, and the top should be attached almost above the ceiling itself. If the size of the cage is minimal, more than four perches should not be placed in it, since unnecessary objects will limit the already small space for the feathered inhabitant.

The health of the parrot will be ensured by perches made of soft wood (willow or birch, you can directly with the buds). Soft rope will also work. Plastics and bamboo cause calluses on the paws of the bird, and even bloody wounds from the sandpaper, which producers sometimes use to wrap their roosts to grind off their claws and beak. It is good if the perches have different thicknesses, this will also provide excellent gymnastics for the parrot’s legs. The fastening of the perches must be rigid: in the process of rocking, the cockatiel can injure long wings or tail.

It should also be understood that the perches are consumables. Parrots happily nibble on them, this is very useful for the digestive system of birds, so periodically such accessories will need to be updated.

You can diversify the life of a winged pet by equipping the cage with various toys. The easiest option is a small mirror or bell. But do not get carried away: first of all, the parrot needs the spaciousness of its home.

DIY cockatiel parrot cage

A good cage for a parrot is quite expensive, especially when it comes to housing for a relatively large and active bird. But, with the patience and some skills, you can effortlessly make an excellent alternative version of the cage with your own hands.

Detailed instructions for building a cockatiel cage are given below.

Material

The material from which the cage is made must meet the following requirements:

  • environmental Safety;
  • strength;
  • smoothness (so that the bird is not injured on sharp edges, corners, protruding objects);
  • the ability to quickly clean.

From this point of view, the tree, beloved for its naturalness and environmental friendliness, is poorly suited as a material for a bird house.

Caring for it is quite complicated, it is heavy, it is inconvenient to wash and clean such material, and in addition, dangerous pests can easily start in it. It is impossible to process the boards with special antiparasitic materials. they can cause poisoning in the feathered tenant. Plywood is a lighter material, but it also has its drawbacks. As an acceptable option, you can consider MDF wood fiber board due to its high environmental friendliness or thinner fiberboard.

Nevertheless, such materials are suitable only for a pallet and only in the case of making a home for a bird in an artisanal way, however, even in this situation, it is better to use modern products of the chemical industry. plastic or organic glass.

It is important to make sure that the material is strong enough: the bird is unlikely to be able to damage it, but its owner during harvesting or just passing by is quite likely.

It is good if the pallet design provides for high sides. In this case, the waste products of the parrot will not get enough sleep from the cage and spread throughout the house. Some models provide for an additional grate, which is laid on top of the pallet, preventing bird poisoning by pecking off stale food mixed with its own droppings (this debris passes through the grate and becomes inaccessible to the parrot).

READ  How to make a parrot nest with your own hands

In addition, it will keep the bird’s feet dry and clean at all times. Many owners of parrots do not welcome such a design, believing that the cockatiel can be injured by horizontal rods at the bottom of his house, but in reality the likelihood of such an accident is very small, and the advantages are obvious.

As for the walls and roof, here it is best to give preference to stainless rods or mesh, and the distance between the rods (cells) should be at least 20 mm so that the parrot cannot stick its head through the rods and get injured.

Tools and materials

To make a cage at home, you will need:

  • wire mesh with cells 10 x 25 mm;
  • plywood or chipboard sheet (part of old furniture will do);
  • metallic profile;
  • self-tapping screws, small nails;
  • scissors for metal;
  • hacksaw;
  • screwdriver;
  • hammer.

An important point: Parrots love to taste everything around. Make sure materials are safe.

Suitable place for a cell in an apartment

When considering the appearance of a good cage, you need to consider its future location. Here are the places where you should definitely not put it:

  • on the windowsill;
  • on the floor;
  • in indoor plants;
  • next to the heating radiator;
  • on the refrigerator.

The kitchen is not the best place for a parrot. There are noisy household appliances, the heat from cooking food, the sound of pouring water. Parrots will not be able to get enough sleep. In the nursery or in the bedroom, on the contrary, the owners will be deprived of a quiet rest due to bird cooing. It is optimal to place the cage in a room where family members are often during the day and no one is there at night. For example, in the living room. It is not at all necessary to be close for a long time, it is enough that the birds observe and feel people nearby.

  • the location of the house for your parrot on the floor or in front of the TV is unacceptable;
  • it is considered normal not to hang the cage from the ceiling or wall, but to place it on a horizontal surface: a bedside table, a table, a cabinet shelf;
  • you should not push the house into the far corner, but it is also undesirable to put it in the middle of the room. It is important for parrots to feel safe and secure;
  • one side of the enclosure should be directed along the wall, the other. facing the light source;
  • you need to protect parrots from direct sunlight, shading part of the grate.

Attention! The best place for a cage is an area at a height of 60 cm from the floor, 2. 3 cm from the wall, away from equipment, sockets, flowers.

Manufacturing steps

So, the materials and tools are assembled, the drawings are ready, it’s time to start assembling the structure.

  • We cut out the base from a sheet of chipboard. this is a guideline for further patterns;
  • According to the size of the bottom, we cut the side walls and the roof from the mesh;
  • We make protective boards from chipboard inside along the perimeter;
  • Having made a marking with a pencil, we drill holes with a diameter of 2 mm in a wooden base with a step of 25 mm;
  • We insert a wire mesh into the resulting punctures, all four walls;
  • We fix the adjacent walls to each other using wooden corners;
  • Install the ceiling in the same way. On the ceiling, you can make either a solid mesh or opening doors;
  • Bend the wire under the bottom and nail down a sheet of plywood to hide the sharp ends;
  • We cut out a flap door or a hole for a separately installed door in one wall (it is better to do this in advance, before assembly).

Such a set of materials and a simple algorithm allow you to make the simplest cage for a parrot with your own hands. Even a beginner can handle this kind of work.

Manufacturing instruction

So how do you make a cage for a small parrot with your own hands? Initially, you need to think about the design, calculate the preliminary dimensions and draw a sketch. Then you should draw the drawings. Having a clear idea of ​​the future structure, you can get to work.

Optimal size and shape

Even a small bird needs a lot of space, otherwise the quality of life deteriorates. The cramped structure limits mobility, while the parrot is forced to sit on the perch, instead of fluttering for pleasure. The cage should not be a place of confinement for a parrot. this is his home, so before construction you need to think over all the little things.

One of the main parameters of a budgerigar cage is size. The size should correspond to the number of residents and their height:

  • for a chick just separated from its parents, a small temporary house is enough: length and width 25 cm each, height 40 cm;
  • an adult needs a more spacious cage: from 40 cm in length and width, from 50 cm in height;
  • two parrots are quite freely placed in a half-meter product 60 cm high, and with each subsequent bird the sizes should increase proportionally.

The larger the cage, the better for the wards, but problematic for the owner: the cleaning area increases, the useful volume of the room decreases.

The preferred house shape for a new pet is rectangular with horizontal and vertical rods. The angular design serves as a safe haven for the parrot. The shy wavy can hide in a secluded corner, away from prying eyes. Tall round cages with a domed top are designed for accustomed parrots and small groups.

Note: Products of bizarre shapes look attractive, but they are not very convenient for cleaning.

How to make a parrot cage with your own hands

Making a comfortable parrot cage with your own hands is not as difficult as it seems. A new cozy house is the best gift for a budgerigar, because the bird spends in it almost all the time. A fragile bird needs reliability, protection and comfort. A homemade cage meets all safety conditions, and also allows you to save a little. From the article you will learn how to make a cage suitable for a budgerigar, how to fill it and where to place it.

Accessories for equipping the cage

When the cage is ready, the moment comes for its arrangement. The list of things a parrot needs includes:

  • automatic drinker, fixed on the rods;
  • a closed feeder with an automatic feeding mechanism (feed is poured into it immediately for a day);
  • wooden perches with a diameter of 1.5. 2 cm.
  • A ladder or a suspension bridge is made of twigs: having cut fragments of a suitable length, they are fastened together with twine;
  • Homemade swing: a piece of a thick branch is drilled along the edges, a strong wire is inserted into the holes and hung in a convenient place;
  • Old rattles, plastic lids, and other household items come in handy as toys.

In such a simple way, a cage is equipped without special costs.

When choosing interior items, do not be afraid to show your imagination. Of course, do not get too carried away, otherwise there is a possibility that the pet will not have enough space. Not only functionality is required from the cage. it should also be spacious so that, moving between objects, the parrot does not get confused and does not get injured.

I’ll parrot the cage with my own hands. Crafting tips

As noted above, first of all, it is necessary to determine the shape and size of the future cell, after which you can proceed to creating a sketch. It should be detailed enough to reflect all the dimensions you want.

Below is an approximate list of the main elements that make up a standard cage. You can make any house for a parrot with your own hands: from the smallest cage to a spacious aviary. All variants have the following components in their design:

  • Pallet. For it, you can use a ready-made box or make it from fiberboard and slats. In this case, you should pay attention to the height of the sides, they should not be very low.
  • Frame (it is a mesh, bent in the desired shape and high-quality fixed to the frame).
  • Roof.

Types of bird cages

First of all, let’s pay attention to the location of the cell. It depends on how your pet will feel, whether he will be comfortable, whether he will feel that he is safe. When making a cage with your own hands, exclude floor options, since by their nature any birds, including parrots, never nest on the ground. If you want to make exactly the floor version, try to make it in such a way that the bottom of the cage is at a height of at least 40 cm from the floor.

Here are a number of factors to look out for when choosing a ready-made cage or creating one yourself:

Determine the shape and size of the cell

The size and shape of the cage depends directly on the type of bird. The budgerigar cage and the larger species, such as the cockatoo, may not be the same size and shape. That is why the wrong choice will negatively affect your pet’s behavior. Here are a number of recommendations, the implementation of which will allow you to give your parrot a decent existence without any problems.

Parrot cage requirements

No matter how spacious the cage you have purchased, the parrot will still not get enough freedom of movement. You can add comfort to the place of detention by providing your pet with the ability to constantly change its location and move more. This requires a properly equipped cage. With your own hands for a parrot, you can create a real paradise. The main thing is not to skimp on materials and their quality.

In addition to being large, the cage should also be equipped with numerous perches and platforms on which your parrot can sit, play, spread its wings and jump from place to place. An important point: if you notice that your pet spends almost all the time sitting at the bottom of the cage, then perhaps he does not have enough room to move. In this case, you need to replace the house with a more spacious version.

Recommended cell sizes

So, the smallest of pets (budgies or blue-headed parrots) need to be kept in a cage, the width of which will be at least sixty centimeters. Medium-sized parrots and Amazons should be housed in houses (cages) that are at least 80 centimeters wide. But the cages for the largest species of these birds differ in that their width is not less than 1 meter. A homemade cage differs from factory options in that during manufacturing you can make it exactly the size that you need.

Another feature of bird cages: their width should be greater than their height. This is due to the fact that the birds, although they can fly, still move in a horizontal plane, just like you and me.

Do-it-yourself cage for a parrot. How to make a parrot cage

Required materials and work procedure

Everything you need to make your own cage. these are wire, corners, metal profiles, screws and nails. When choosing materials for the cage, it is necessary to give preference to environmentally friendly ones that cannot harm the life and health of your beloved pet.

The beginning of the process of making the cage provides for the moment of preparing the framework. Making them is pretty simple, all you need to pay attention to. this is their high strength. Each of the frames consists of four separate elements (blanks).

The next step involves creating the side pieces using a metal profile. That part of the side walls that is longitudinal in nature should be bent at an angle of 90 degrees and fastened to the lower and upper parts. Parts of the frame are attached with self-tapping screws. Since you know the dimensions of the frames, the required amount of mesh is cut in accordance with them, which must be adjusted to the edge of the profile. After marking the intersections of the wire and the frame, you need to drill the holes. They must correspond to the diametrical size of the wire from which the mesh is made.

How To Make A Large Bird Cage Pt.1/2

Do not forget to equip the finished cage with special hooks, which are needed in order to fix various accessories (perches, feeder, drinker, etc.).

As for the cleanliness and care of the parrot, a pull-out tray is very convenient in this regard. It will not be difficult to make one. For it, you will need a frame made of a profile and a sheet of galvanized metal. By connecting them, you get a pull-out tray.

The cage door also requires special attention. The easiest way to arrange it is to cut a hole in the mesh. But at the same time, you should pay attention to its size (not very large) and location (closing from top to bottom).

That’s all! A do-it-yourself cage made and equipped for a parrot or other bird is ready. You can introduce your pet to a new apartment.

FUNDAYUNA.COM 2021